Replacing Pinion Bearing Jinma 354

Bob,

Bummer about that. When you say it will not go into low gear, does that mean it will not go into low range?

I am very curious about the gearing in your 354. PLEASE take and post many pictures. We all need to see your repair efforts so as to learn all about it. You have an incredible opportunity to share a wealth of information for all of us here on the forum. So Please take the time to post pictures and a description of everything.

I will do the best I can, I have not taken mine apart, but have looked into my Jinma 354 transmission several times and have taken many pictures of all the gears.

To remove the upper and lower shafts, the transmission will need to be completely dismantled.

Remove the bell housing from the front of the transmission, if you have not already done so.

Drive out all roll pins for all shifter forks, remove the shifter fork slider shafts, then the slider forks.

Unbolt the front bearing retainer flanges, pull out the shaft a little at a time while lifting out the gears. There are many parts bushings, bearings, gears, etc so be very careful to note how it comes apart so it can go back together properly.

Here are a few pictures- the first one is a top view standing on the right side of the tractor looking down into the Transmission of my Jinma 354 . The following pics are from the parts manual to aid you in how everything is put together.

Does your transmission look EXACTLY like the "live" picture of mine? Please pay particular attention to the reverse idler and the configuration of all the gears. I have been trying to find out if Jinma has two versions of the 354 transmission. So far no one has been able to give me any straight answers. The parts book shows several gear options and "user selectable" gears. But no one knows exactly what combination of gears are needed and what it does to the ratios. I would love to SLOW DOWN my tractor, it is WAY too fast in the Hi range. I suspect yours is too - Is that right? especially reverse, what do you think of the reverse speed in high range?




I am willing to help the best I can, please reciprocate by posting a boat load of pictures.


Thanks,
Larry

As promised,

Here are pictures when we first split transmission from bell housing.


The next set show disassembly so far. We have removed shifter forks, reverse idler, front bearing holders and attempted to remove front bearings. I have noted how pinion bearing has moved from case and how bearings appear pressed onto shaft.





Last picture is of differential. This is way I think the lower shaft will have to come out. The round tubes are the shifter rails that were slid back from transmission case.


Bob

And just to put a pretty face to a name

Me and my five grandsons taken about 1 year ago @ Fort Flagler, WA. Two more grandchildren due in July. One will be a boy, the other will not be known until b-day.

Bob, I agree ... a great looking bunch you have there...and welcome to the forum.
Regarding the transmission, there is something wrong if those bearings fit the shafts so tight. That would make an assembly nightmare! How would you ever position them if you couldn't move them into location once the shaft is in the housing?
Seeing what you are going through, my hat is off to you and your brother for tackling that job. I might have been tempted to tap that bearing which moved out of it's retainer pocket back into place and installed a press fit dowel to keep it there or a SHCS to retain the flange.

With the bearings being tight, you might ruin them upon disassembly, much like that one you talked about. Is there a way for you to add some heat to the bearing races to slip them off the shafts? Upon reassembly, I'd use some wet and dry 320 or 400 paper on the shaft while spinning it in a lathe or something. That is to fit the new bearings first, so they don't bind on the shaft like that. There's no reason for them to be like that.
Good luck and keep us posted.
Rob-♦

That's a great pic of you and the kids... Wow 5 and two on the way....

Thanks for compliments on my grandkids. They all love the tractor. Lots of levers and stuff to yank and push on. All grandpas should have at least one tractor.

Looks like more interest in the grandkids. Tractor can wait. Here is one we took last Christmas. From left to right Wesley, George, Sean, Zephyr and Brody




Bob

UPDATE

I just spoke with the mechanic @ Keno Tractors in Oregon. He was very helpful. He has not disassembled any 354 transaxle, but they have done a few 284s.

On the 284's he said the whole thing comes apart. Every nut, bolt, pin. etc. in transmission case and differential. The pinion bearing is first thing that goes in assembly and last thing out in disassembly. He also said that he had to drive most of the bearings off the shafts and out of case. He used a combination of techniques to remove the bearings and destroyed a few bearings in the process.

FYI, I asked him why they had to repair the 284. He said that the bolts that hold the shifter plate has come loose and fell into transmission causing all sorts of damage. So, you folks that have 284's might want to take a good look at that area.

UPDATE

Brother and I completed disassembly of tractor today. We started around 10:00 am and finished about 4:00 pm. We spent most of our time figuring out best way to tackle problems and keeping things organized.

I took a lot of pictures and will post along with procedures we used to disassemble. (Little tired right now) The biggest problem turned out to be the two bearings on the front of both shafts. Once we removed them, everything else came apart fairly easy.

As I suspected, the circlip in front of pinion bearing was not in its grove which I believe allowed pinion bearing to move forward. I am trying to determine if this was problem in assembly or some force in tractor pushed it out. It would seem that it is assembly related because to my knowledge there have been no other reports of this failure.

Thanks to everyone for your support

Bob